(五)、Common fault diagnosis and treatment: 1, switch on the power, electromagnetic valve will not work properly. A, coil burned or short circuit -- replacing coil B, valve core was impurities stuck - removed, cleared by professionals and assembled. 2, disconnect the power, solenoid valves don't work properly. Valve core was impurities stuck - removed, cleared by professionals and assembled. 3, leak a quantity to exceed bid. |
GERMANY LIK VALVE COMPANY LIMITED High-pressure electromagnetic valve instructions for use (一)、Product use Electromagnetic valve as automatic control and remote control a actuators, it is widely used in Metallurgy, petrochemical, textile, pharmaceutical, food, tobacco, defense, scientific research, and other various fields, The circulation medium separately for steam, air, oil, water and gas, refrigerants, etc | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
(二)、Working principle When the coil electricity, moving iron core suck close, pilot valve mouth is open, make the main valve, the main valve fortress cavity step-down because of pressure differential open, fill medium circulation. When the coil without electricity, moving iron core reset, pilot valve mouth closed, make the main valve, the main fortress chamber pressurization plug press, electromagnetic valve is closed. 【德国莱克(LIK)流体电磁阀】 进口高压电磁阀|进口高压高温电磁阀| 高压电磁阀 | 超高压电磁阀 | 高温、蒸汽电磁阀 | 超高温电磁阀 | 直角直动式电磁阀 | 高温高压电磁阀 | 制冷电磁阀 | 超低温电磁阀 | 双向电磁阀 | 双稳态自保持电磁阀 | 防腐电磁阀 | 真空电磁阀 | 脉冲电磁阀 | 微型电磁阀 | 三通电磁阀 | 塑料电磁阀 | 直动式电磁阀 【德国莱克(LIK)特种及专用电磁阀】 燃气电磁阀 | 消防电磁阀 | 油用电磁阀 |进口高温电磁阀| 锅炉回水专用电磁阀 | 太阳能专用电磁阀 | 四通多流体电磁阀 液压电磁阀 两位三通电磁阀 | 两位四通电磁阀 | 两位五通电磁阀 | 三位三通电磁阀 | 三位四通电磁阀 | 三位五通电磁阀 | 三位六通电磁阀 【产品用途】 德国莱克LIK电磁阀作为自动控制及远程控制的一个执行器,它广泛应用于高压系统、蒸汽系统、低温系统、工业石油供用系统、灌装系统、供热系统、储罐系统、电厂设备、石化设备、真空设备、气动设备、消防设备、管道自控工程等。 工作原理 当线圈通电,动铁芯吸合,先导阀口处于开启状态,使主阀塞上腔降压,主阀塞因压差开启,介质流通。 当线圈断电,动铁芯复位,先导阀口处于关闭状态,使主阀塞上腔升压,将主阀塞压下,电磁阀关闭 【德国莱克LIK磁阀技术参数】
安装与维护: 1、现场安装必须按照国家防爆危险场所“电气安全规程”中有关规定进行。 2、电磁阀内外接地,必须牢固可靠。 3、电磁阀引出电缆导线为三根,其中一根为接地线,另二根为工作导线。 4、电磁阀安装前应将管路内部清洗干净。 5、电磁阀有杂质时,进口端前必须安装密度0.5mm的过滤器。 6、安装电磁阀时注意阀体上箭头要求与介质流向一致。 7、电磁阀应垂直安装,线圈在上。 8、电磁阀维修时应断电后开盖,非电器人员不得拆卸电磁阀电气部件。 电磁阀产品分类方式
德国莱克(LIK)电磁阀是用来控制流体的自动化基础元件,属于执行器;并不限于液压,气动。电磁阀用于控制液压流动方向,工厂的机械装置一般都由液压钢控制,所以就会用到电磁阀。 高温电磁阀的安装及维护 高温电磁阀特点:耐高温,采用金属硬密封,提高了使用温度。耐磨:选材合理,阀杯和导向套间巧秒地利用流体的润滑作用,减少磨损。 |
(四)、Installation and maintenance: 1, site installation must, in accordance with state explosion-proof dangerous places "electrical safety procedures" codes. 2, electromagnetic valve internal and external grounding, we must firmly and reliable. Three, solenoid valve lead wires for three pillars and cable grounding lines for one of the roots for work, the other two wires. 4, electromagnetic valve before installation should clean the inside of the pipeline. 5, solenoid valve impurity, the inlet of 0.5 mm before must be installed density of filters. 6, install solenoid valves on the body that should pay attention to the flow direction of medium consistent with arrows requirements. 7, electromagnetic valve should be installed vertically, the coil. 8, electromagnetic valve should be after powrefailure open repair, the electrical appliances personnel shall not cover remove electromagnetic valve electric components 。 |
{{item.AppContent}}